32 WCC Lite internal signals
Overview
The WCC Lite contains several internal data points for readout and control which can be accessed via the Pooler service.
Configuration
Devices section
In the devices section, only the protocol, scan_rate_ms and poll_delay_ms are to be configured for this type of device.
WCC Lite internal signals
Parameter | Type | Description | Required |
Default Value (when not specified) |
Range |
name |
string |
User-friendly device name | Yes | ||
device_alias | string | Alphanumeric string to identify a device | Yes | ||
protocol | Protocol identifier Internal data | Yes | Internal data | ||
scan_rate_ms | integer | Update rate | No | 60000 | |
poll_delay_ms | integer | Poll delay | No | 200 |
It is advised to set scan_rate_ms to a value greater than 5000 ms as frequent scans may result in significant overload of the pooler process.
Signals section
tag_job
defines the tag job. This can be set to gpio
, board
, netstat
, led
and process
. tag_job_todo
defines the job sub job. This field should address the particular point of interest.
job_todo | Description | tag_job_todo | Description |
gpio |
Get GPIO | GPIO number | Use number 11 for onboard digital input; SIM select 12; SIM detect 20 |
Set GPIO | [integer]|[1/0] | Set gpio number to high or low | |
board |
Board info |
active-sim-iccid | Active SIM ICCID |
active-sim | Active SIM card | ||
cpu-usage | CPU usage | ||
duid | DUID | ||
fw-version | Firmware version | ||
gsm-available-rat | GSM available radio access technologies |
||
gsm-current-rat | GSM current radio access technology |
||
gsm-current-rat-num | GSM current radio access technology identifier |
||
gsm-imsi | GSM IMSI number | ||
gsm-internet-status | GSM Internet status | ||
internet-status | Same as gsm-internet-status | ||
gsm-network-reg-status | GSM network register status | ||
gsm-operator | GSM operator | ||
gsm-operator-num | GSM operator number | ||
gsm-roaming-status | GSM roaming status | ||
gsm-selected-rat | GSM selected rat | ||
gsm-service-provider | GSM service provider | ||
gsm-signal-quality | GSM signal quality | ||
gsm-signal-quality-num | GSM signal quality (dBm) | ||
gsm-sig-quality | Same as gsm-signal-quality-num | ||
hostname | Hostname | ||
hw-info | Hardware information | ||
modem-imei | Modem IMEI number | ||
modem-manufacturer | Modem manufacturer name | ||
modem-model | Modem model | ||
modem-type | Modem type | ||
ram-usage | RAM usage | ||
sim-status | SIM card status | ||
uuid | UUID | ||
netstat|[interface] | Network statistics |
TX |
Bytes transferred |
RX | Bytes received | ||
smsstat |
SMS statistics |
received |
SMS received |
sent |
SMS sent | ||
call |
SMS call | ||
failed |
SMS failed | ||
led |
LED status/control |
ath9k-phy0 | WLAN LED |
wcclite:blue:heartbeat | Status LED | ||
wcclite:blue:wlan | WLAN LED | ||
wcclite:green:eth0 | ETH0 LED | ||
wcclite:green:eth1 | ETH1 LED | ||
wcclite:green:signal1 | Signal 1 LED | ||
wcclite:green:signal2 | Signal 2 LED | ||
wcclite:green:signal3 | Signal 3 LED | ||
wcclite:gsm-rst | GSM LED | ||
wcclite:red:fault | Fault LED | ||
wcclite:rs232-en | RS LED | ||
wcclite:relay | Relay LED & Output | ||
process | Check if process is running | [process name] | 1 or 0 is returned |
Assigning source signals to tags other than wcclite:relay may cause undesirable effects. Signals other than wcclite:relay should be used for monitoring only.