| **Parameter** | **Type** | **Description** | **Required** | **Default Value** (when not specified) | **Range** |
| name | string | User-friendly device name | Yes | ||
| device\_alias | string | Alphanumeric string to identify a device | Yes | ||
| protocol | Protocol identifier Internal data | Yes | **Internal data** | ||
| scan\_rate\_ms | integer | Update rate | No | 60000 | |
| poll\_delay\_ms | integer | Poll delay | No | 200 |
It is advised to set scan\_rate\_ms to a value greater than 5000 ms as frequent scans may result in significant overload of the pooler process.
#### Signals section `tag_job` defines the tag job. This can be set to `gpio`, `board`, `netstat`, `led` and `process`. `tag_job_todo` defines the job sub job. This field should address the particular point of interest.| **job\_todo** | **Description** | **tag\_job\_todo** | **Description** |
| gpio | Get GPIO | GPIO number | Use number 11 for onboard digital input; SIM select 12; SIM detect 20 |
| Set GPIO | \[integer\]|\[1/0\] | Set gpio number to high or low | |
| board | Board info | active-sim-iccid | Active SIM ICCID |
| active-sim | Active SIM card | ||
| cpu-usage | CPU usage | ||
| duid | DUID | ||
| fw-version | Firmware version | ||
| gsm-available-rat | GSM available radio access technologies | ||
| gsm-current-rat | GSM current radio access technology | ||
| gsm-current-rat-num | GSM current radio access technology identifier | ||
| gsm-imsi | GSM IMSI number | ||
| gsm-internet-status | GSM Internet status | ||
| internet-status | Same as gsm-internet-status | ||
| gsm-network-reg-status | GSM network register status | ||
| gsm-operator | GSM operator | ||
| gsm-operator-num | GSM operator number | ||
| gsm-roaming-status | GSM roaming status | ||
| gsm-selected-rat | GSM selected rat | ||
| gsm-service-provider | GSM service provider | ||
| gsm-signal-quality | GSM signal quality | ||
| gsm-signal-quality-num | GSM signal quality (dBm) | ||
| gsm-sig-quality | Same as gsm-signal-quality-num | ||
| hostname | Hostname | ||
| hw-info | Hardware information | ||
| modem-imei | Modem IMEI number | ||
| modem-manufacturer | Modem manufacturer name | ||
| modem-model | Modem model | ||
| modem-type | Modem type | ||
| ram-usage | RAM usage | ||
| sim-status | SIM card status | ||
| uuid | UUID | ||
| netstat|\[interface\] | Network statistics | TX | Bytes transferred |
| RX | Bytes received | ||
| smsstat | SMS statistics | received | SMS received |
| sent | SMS sent | ||
| call | SMS call | ||
| failed | SMS failed | ||
| led | LED status/control | ath9k-phy0 | WLAN LED |
| wcclite:blue:heartbeat | Status LED | ||
| wcclite:blue:wlan | WLAN LED | ||
| wcclite:green:eth0 | ETH0 LED | ||
| wcclite:green:eth1 | ETH1 LED | ||
| wcclite:green:signal1 | Signal 1 LED | ||
| wcclite:green:signal2 | Signal 2 LED | ||
| wcclite:green:signal3 | Signal 3 LED | ||
| wcclite:gsm-rst | GSM LED | ||
| wcclite:red:fault | Fault LED | ||
| wcclite:rs232-en | RS LED | ||
| wcclite:relay | Relay LED & Output | ||
| process | Check if process is running | \[process name\] | 1 or 0 is returned |
Assigning source signals to tags other than wcclite:relay may cause undesirable effects. Signals other than wcclite:relay should be used for monitoring only.