16.13 M-Bus
Overview
M-Bus or Meter-Bus is a protocol for the remote reading of water, gas, or electricity meters. M-Bus is also usable for other types of consumption meters, such as heating systems or water meters. The M-Bus interface is made for communication on two wires, making it cost-effective. M-bus over TCP is also supported. When configured, meters will deliver the data they have collected to a WCC Lite RTU that is connected at periodic intervals (scan_rate_ms) to read all utility meters.
Configuration
M-Bus parameters for Device tab
| Parameter |
Type |
Description |
Required |
Default Value (when not specified) |
Range |
||
|---|---|---|---|---|---|---|---|
| TCP | RTU | Min | Max | ||||
| name | string | User-friendly device name | Yes | Yes |
|
|
|
| description | string | Description of a device | No | No |
|
|
|
| device_alias | string | Alphanumeric string to identify a device | Yes | Yes | |||
| enable | boolean | Enabling/disabling a device | No | No | 1 | 0 | 1 |
| protocol | string | Protocol to be used. | Yes | Yes | mbus serial, mbus tcp | ||
| scan_rate_ms | integer | All reads and writes will be executed within the timeframe in milliseconds. | No | No | 10000 |
|
|
| poll_delay_ms | integer | Minimum time delay in milliseconds to wait before sending any data on port. |
No | No | 200 |
|
|
| timeout_ms | integer | Timeout of waiting for an incoming response in milliseconds | Yes | Yes | 0 | 60000 | |
| address | string | Device address | Yes | Yes | |||
| device | string | Communication port | - | Yes | PORT1 | PORT2 | |
| baudrate | integer |
Communication speed (baud/s) |
- |
No |
9600 |
300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
|
| databits | integer |
Data bit count for communication |
- |
No |
8 |
6 |
9 |
| stopbits | integer |
Stop bit count for communication |
- |
No |
1 |
1 |
2 |
| parity |
string |
Communication parity option |
- |
No |
none |
none, even, odd |
|
|
serial_close_delay
|
integer | Delay before closing the serial connection. | - | No | 400 | ||
| ip | string | The IP address of the TCP slave device | Yes | - | |||
| port | integer |
TCP communication port |
Yes |
- |
|
0 | 65535 |
M-Bus parameters for the Signals tab
| Parameter |
Type |
Description |
Required |
Default Value (when not specified) |
Range |
||
|---|---|---|---|---|---|---|---|
| TCP | RTU | Min | Max | ||||
| signal_name |
string |
User-friendly signal name |
Yes | Yes |
|
|
|
| device_alias |
string |
Device alias from a Devices tab |
Yes | Yes |
|
|
|
| signal_alias |
string |
Unique alphanumeric name of the signal to be used |
Yes | Yes |
|
|
|
| enable |
boolean |
Enabling/disabling of an individual signal |
No | No | 1 |
0 |
1 |
| log |
integer |
Enable logging in the event log |
No | No | 0 |
|
|
| number_type | string | Type of a number (FLOAT, DOUBLE, DIGITAL, etc.) | Yes | Yes | |||
| job_todo |
string |
Tag job as single or multiple comma-separated OBIS codes |
Yes | Yes |
|
|
|
| tag_job_todo | string | Tag sub job | Yes | Yes | |||