Search Results

The page shows information about current interface status, its configurations, provides various interface, network properties configuration capabilities and contains the following subsections:• INTERFACES: shows information about current interface status, al...

WCC Lite has an optional Dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 5: WCC Lite Dual-SIM card slot

Introduction Lua is a powerful, efficient, lightweight scripting language. It has been used in many industrial applications with an emphasis on embedded systems. Lua has a deserved reputation for performance. To claim to be "as fast as Lua" is an aspiration o...

WCC Lite is based on OpenWRT operating system. OpenWrt is described as a Linux distribution for embedded devices. WCC Lite has same functionality as Linux OS including user management. Basic configuration on WCC Lite can be done using web based frontend. More...

System Processor ARM CPU (AR9331, 400MHz) Memory 16 MB Flash/64 MB DDR2 RAM Wireless 802.11 b/g/n I/O 1x Binary input (hardware version >=1.4) 1x Relay output Additional storage SD card (2GB by default) SD card (2GB by default) ...

The reset button is located on the front panel of WCC Lite, to access it, remove a transparent front panel cover. Different time lengths of button pressing call different behavior. Pressing time Description Indication Short Press System reboot ...

Figure 1: Front panel status indication

WCC Lite has an optional Dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 6: WCC Lite Dual-SIM card holder To insert SIM cards, r...

It is recommended to power WCC Lite from 6W (minimum) 12-24V DC power supply. A full range is 5V to 36V. Figure 3: Power input connector Note: Make sure that the device is compatible with your power source before proceeding! Check the label next to the pow...

To log out of the device graphical user interface a logout button in the interface’s upper right corner should be pressed. A user is automatically disconnected after ten minutes of inactivity. This ensures that the device would not be suspect to any delibera...

To mount the device: Secure the top of the mounting clip onto a DIN rail. Push the bottom of a device forward to fix the clip in place. To dismount the device: Pull red-colored clip downwards (found at the bottom side of the DIN rail). Pull back the...

For hardware versions older than version 1.3, in case a Wi-Fi connection is needed, connect a Wi-fi antenna to the SMA connector labeled “WIFI“. Select a good antenna placement spot considering the operation environment. Figure 13: Wi-Fi antenna connector (...

WCC Lite comes with an optional GSM module.There are a few hardware configurations available:  Without GSM modem. With single SIM modem (HW version 1.0 - 1.2) - 2G/3G (GPRS, EDGE / UMTS, HSDPA, HSUPA) version - 5.76Mb/s upload, 7.2Mb/s download. UMTS/HSPA ...

With WCC Lite hardware version 1.4 a digital input functionality has been introduced. Software configuration guidelines are discussed later in this document. Figure 11: Signal relay connector 

WCC Lite integrates 1 signal relay (3-way RO connector) with COM (common), NC (normally closed), and NO (normally open) signals. Figure 10: Signal relay connector Maximum switching power is 60W, maximum contact current is 2A, maximum switching voltage is 6...

WCC Lite WCC Lite has 2 serial ports (Figure 7). Selectable RS485 (by default) or RS232 interface on PORT1 and RS485 interface on PORT2. Figure 7: WCC Lite ports  WCC Lite RS485 interface supports baud rates up to 115200 and has an integrated 120 terminati...

Single point Commonly used in storing digital states single point values have only one bit of information. The value of such tags can be either one or zero. On the internal web of WCC Lite states of this type of tags are shown in colored boxes with customisab...

Upload of firmware through USB to IOMod device is done through CLI (Command Line Interface) on virtual COM port. Drivers needed for MS Windows to install VCOM will be provided. To open up CLI simply connect to specific VCOM port with terminal software (it is a...