Search Results

Overview Elgama protocol is used for communications with Elagama elektronika electricity meters. Configuration Available meter types (use number only): 0 ­ EPQM/LZQM 1 ­ EPQS 2 ­ GAMA300 3 ­ GAMA100 4 ­ ITS cl Elgama parameters for Device tab ...

WCC Lite WCC Lite has 2 serial ports (Figure 7). Selectable RS485 (by default) or RS232 interface on PORT1 and RS485 interface on PORT2. Figure 7: WCC Lite ports  WCC Lite RS485 interface supports baud rates up to 115200 and has an integrated 120 terminati...

Protocol HUB section stores configuration for every connected device. You can configure it by importing settings from an Excel file. Configuration In this tab a user can: Import new configuration from Excel file (.xls, .xlsx formats). If any errors in t...

It provides the main navigation through the website. Contains the following sections: PROTOCOL HUB: configuration related to data exchange between WCC Lite and other devices. STATUS: system information and diagnostics. SYSTEM: basic system settings such...

WCC Lite comes with a static network configuration with its IP set to 192.168.1.1. For initial setup set a static IP address on your computer and connect your network card to the WCC Lite with an ethernet cable. 8.1.1 Static IP address setup on Windows 1. Pr...

For hardware versions older than version 1.3, in case a Wi-Fi connection is needed, connect a Wi-fi antenna to the SMA connector labeled “WIFI“. Select a good antenna placement spot considering the operation environment. Figure 13: Wi-Fi antenna connector (...

WCC Lite comes with an optional GSM module.There are a few hardware configurations available:  Without GSM modem. With single SIM modem (HW version 1.0 - 1.2) - 2G/3G (GPRS, EDGE / UMTS, HSDPA, HSUPA) version - 5.76Mb/s upload, 7.2Mb/s download. UMTS/HSPA ...

With WCC Lite hardware version 1.4 a digital input functionality has been introduced. Software configuration guidelines are discussed later in this document. Figure 11: Signal digital input 

WCC Lite integrates 1 signal relay (3-way RO connector) with COM (common), NC (normally closed), and NO (normally open) signals. Figure 10: Signal relay connector Maximum switching power is 60W, maximum contact current is 2A, maximum switching voltage is 6...

WCC Lite has an optional Dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 6: WCC Lite Dual-SIM card holder To insert SIM cards, r...

Overview SMA Net can transfer SMA Data, TCP/IP and many more telegrams due to its multi­protocol capability. Thus, it is the preferred telegram frame in case of new developments. Configuration SMA NET parameters for Device tab Parameter Type Descri...

WCC Lite has an optional Dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 5: WCC Lite Dual-SIM card slot

It is recommended to power WCC Lite from 6W (minimum) 12-24V DC power supply. A full range is 5V to 36V. Figure 3: Power input connector Note: Make sure that the device is compatible with your power source before proceeding! Check the label next to the pow...

To mount the device: Secure the top of the mounting clip onto a DIN rail. Push the bottom of a device forward to fix the clip in place. To dismount the device: Pull red-colored clip downwards (found at the bottom side of the DIN rail). Pull back the...

The reset button is located on the front panel of WCC Lite, to access it, remove a transparent front panel cover. Different time lengths of button pressing call different behavior. Pressing time Description Indication Short Press System reboot ...

Figure 1: Front panel status indication

Introduction IEC 62056 is a set of standards for electricity metering data exchange by International Electrotechnical Commission. The IEC 62056 standards are the international standard versions of the DLMS/COSEM specification. DLMS or Device Language Messag...

WCC Lite is based on OpenWRT operating system. OpenWrt is described as a Linux distribution for embedded devices. WCC Lite has same functionality as Linux OS including user management. Basic configuration on WCC Lite can be done using web based frontend. More...

Overview Windlog protocol is used for communications with the Windlog data logger. Configuration Windlog parameters for Device tab Parameter Type Description Required Default value (when not specified) Range Min Max n...

Overview System System section in the status tab shows basic information about the current status of the system.Hostname: The label that is used to identify the device in the network.Model: Model of the device.Firmware version: Current firmware version.Kerne...