Search Results

To log out of the device graphical user interface a logout button in the interface’s upper right corner should be pressed. A user is automatically disconnected after ten minutes of inactivity. This ensures that the device would not be suspected of any deli...

  Figure 1: Front panel status indication

ConMod P1 Manual Manual -> Download

ConMod Firmware 1.0.3 ConMod Firmware --> Download

Overview ConMod P1Modbus is a small industrial protocol converter for smart Meters with P1 interface output to convert meter data into industrial standard protocols Modbus RTU and Modbus TCP with interfaces RS485 and Wi-Fi (2,4GHz). They are designed to conv...

There are two types of command signals used in SMS Receivers: System: reboot wcc/reboot modem – when sending a message with text reboot, the device starts rebooting and after successful reload sends back a message to the sender with text  REBOOT OK.  sw...

SMS receiver is a service responsible for command execution that was received via text message. The service is available on WCC Lite with the modem. To use this service a working SIM card is also required. This chapter will describe command types and configura...

System Processor ARM CPU (AR9331, 400MHz) Memory 16 MB Flash/64 MB DDR2 RAM Wireless 802.11 b/g/n I/O 1x Binary input (hardware version >=1.4) 1x Relay output Additional storage SD card (2GB by default) SD card (2GB...

The reset button is located on the front panel of WCC Lite, to access it, remove a transparent front panel cover. Different time lengths of button pressing call for different behaviour. Pressing time Description Indication Short Press System reb...

WCC Lite has an optional dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 6: WCC Lite Dual-SIM card holder To insert SIM cards, r...

Single point Commonly used in storing digital states single point values have only one bit of information. The value of such tags can be either one or zero. On the internal web of WCC Lite states of this type of tags are shown in colored boxes with customisab...

WCC Lite has an optional Dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 5: WCC Lite Dual-SIM card slot

It is recommended to power WCC Lite from a 6W (minimum) 12-24V DC power supply. A full range is 5V to 36V. Figure 3: Power input connector Note: Make sure that the device is compatible with your power source before proceeding! Check the label next to the p...

To mount the device: Secure the top of the mounting clip onto a DIN rail. Push the bottom of a device forward to fix the clip in place. To dismount the device: Pull the red-coloured clip downwards (found at the bottom side of the DIN rail). Pull bac...

For hardware versions older than version 1.4, in case a Wi-Fi connection is needed, connect a Wi-fi antenna to the SMA connector labelled “WIFI“. Select a good antenna placement spot considering the operation environment. Figure 1. Wi-Fi antenna connector (ha...

WCC Lite comes with an optional GSM module.There are a few hardware configurations available:  Without a GSM modem. With single SIM modem (HW version 1.0 - 1.2) - 2G/3G (GPRS, EDGE / UMTS, HSDPA, HSUPA) version - 5.76Mb/s upload, 7.2Mb/s download. UMTS/HSP...

With WCC Lite hardware version 1.4, a digital input functionality has been introduced. Software configuration guidelines are discussed in the WCC Lite internal signals section. It changes state when the voltage is between 12-48V (The supported range is between...

WCC Lite integrates 1 signal relay (3-way RO connector) with COM (common), NC (normally closed), and NO (normally open) signals. Figure 10: Signal relay connector Maximum switching power is 60W, maximum contact current is 2A, maximum switching voltage is 6...

WCC Lite WCC Lite has 2 serial ports (Figure 7). Selectable RS485 (by default) or RS232 interface on PORT1 and RS485 interface on PORT2. Figure 7: WCC Lite ports  WCC Lite RS485 interface supports baud rates up to 115200 and has an integrated 120 terminati...

Overview ConMod P1Modbus is a small industrial protocol converter for smart Meters with P1 interface output to convert meter data into industrial standard protocols Modbus RTU and Modbus TCP with interfaces RS485 and Wi-Fi (2,4GHz). They are designed to conv...