Search Results

The page shows information about current interface status, its configurations, provides various interface, network properties configuration capabilities and contains the following subsections:• INTERFACES: shows information about current interface status, al...

In order to connect to the WCC Lite: Power up the WCC Lite Once the WCC Lite boots up, plug an ethernet cable into the ETH0 port. Connect the other end of the cable to the Ethernet interface of your PC/Mac Make sure DHCP is enabled on your Ethernet interf...

Copyrights and trademarks Elseta is UAB “Elseta” trademark that identifies UAB “Elseta” manufactured products. All of the products copyright belongs to "Elseta”. These documents and the product properties can not be changed without company “Elseta'” knowledge ...

Device requires USB drivers to work as virtual com port. First-time connection between device and computer could result in “Device driver software was not successfully installed” error.  Device driver error message User then manually installs drivers by sele...

IOMod series devices has USB port for IO module configuration. Due to be accessible on some of Windows OS devices please find attached drivers.  IOmod-USB-driver-V-COM<- download link.

Description This article describes WCC Lite configuration steps to enable Modbus TCP protocol conversion to IEC 104. First steps Before you begin, make sure you have completed all physical installation work according to the manufacturer's installation ins...

Description This article describes WCC Lite configuration steps to enable Comlynx protocol conversion to Modbus TCP First steps Before you begin, make sure you have completed all physical installation work according to the manufacturer's installation in...

In order to enable connected devices communication through the router it is needed to enable Masquerading for outgoing packets on WAN interface: Go to Network → Firewall→ General settings Select Masquerading on WAN interface and click on Save & Apply   ...

The IOmod series comprises devices that incorporate various input and output modules. These modules all operate using one of three firmware versions (except for 4Cs4Vs, which uses one of two). These firmware versions serve to distinguish the communication prot...

Single point Commonly used in storing digital states single point values have only one bit of information. The value of such tags can be either one or zero. On the internal web of WCC Lite states of this type of tags are shown in colored boxes with customisa...

Full Protocol HUB section is only available on “Cloud gateway” firmware type.For “RTU” firmware type refer to Sequence of Events and Imported Signals subsections. Protocol HUB section stores configuration for every connected device. There are three ways to co...

WCC lite supports various interfaces to be acquire data and control external circuitry. That includes two serial port interfaces, relay output, digital input and external cellular connection antennae. Serial port interfaces WCC Lite WCC Lite has 2 serial por...

Mounting To mount the device:1. Secure the top of the mounting clip onto a DIN rail.2. Push the bottom of a device forward to fix the clip in place. To dismount the device:1. Pull red coloured clip downwards (found at the bottom side of the DIN rail).2. Pull...

Status indication Reset button The reset button is located on the front panel of WCC Lite, to access it, remove a transparent front panel cover. Different time lengths of button pressing call different behaviour. Pressing time Description Indication ...

Features • 1xRS485/232; 1xRS485; 2xEthernet• 1 x Digital Input• 1 x Relay output• WIFI, 2G/3G/4G(LTE) integrated communication• 2 SIM card modem• PLC logic• Internal memory: SD card• RTC clock and NTP server/client• Hardware Watchdog• Alarm management• User ...

Description One o the first steps in RTU/Datalogger setting up is to prepare connection to internet or a specific private network over Ethernet or GSM. This article describes WAN over Ethernet connection setup. Setting WAN IP Go to Network → Interfaces →...

To log out of the device graphical user interface a logout button in interface’s upper right corner should be pressed. A user is automatically disconnected after ten minutes of inactivity. This ensures that the device would not be suspect to any deliberate d...

Introduction Services tab shows the services of the device and contains the following subsections: Services tab shows the services of the device and contains the following subsections: TELEMETRY AGENT: device telemetry sending to a remote server; IPSEC:...

Overview System System section in status tab shows basic information about current status of the system.Hostname: The label that is used to identify the device in the network.Model: Model of the device.Firmware version: Current firmware version.Kernel versio...

 Front face                                                                                                                                                  Back face   Power on indicator.                                                                   ...