Search Results

WCC Lite WCC Lite has 2 serial ports (Figure 7). Selectable RS485 (by default) or RS232 interface on PORT1 and RS485 interface on PORT2. Figure 7: WCC Lite ports  WCC Lite RS485 interface supports baud rates up to 115200 and has an integrated 120 terminati...

System Processor MIPS CPU (AR9331, 400MHz) Memory 16 MB Flash/64 MB DDR2 RAM Wireless 802.11 b/g/n I/O 1x Binary input (hardware version >=1.4) 1x Relay output Additional storage SD card (2GB by default) SD card (2G...

To upgrade firmware in ConMod its interface has to be reachable via the Wi-Fi. To do so, connect the ConMod to the meter, turn it on, or connect it to a power source and turn on the wi-fi switch. ConMod then becomes a Wi-Fi access point. To connect to ConMod c...

Overview ConMod P1Modbus is a small industrial protocol converter for smart Meters with P1 interface output to convert meter data into industrial standard protocols Modbus RTU and Modbus TCP with interfaces RS485 and Wi-Fi (2,4GHz). They are designed to conv...

ConMod P1 Manual Manual -> Download

ConMod Firmware 1.0.3 ConMod Firmware --> Download

Overview ConMod P1Modbus is a small industrial protocol converter for smart Meters with P1 interface output to convert meter data into industrial standard protocols Modbus RTU and Modbus TCP with interfaces RS485 and Wi-Fi (2,4GHz). They are designed to conv...

There are two types of command signals used in SMS Receivers: System: reboot wcc/reboot modem – when sending a message with text reboot, the device starts rebooting and after successful reload sends back a message to the sender with text  REBOOT OK.  sw...

SMS receiver is a service responsible for command execution that was received via text message. The service is available on WCC Lite with the modem. To use this service a working SIM card is also required. This chapter will describe command types and configura...

The reset button is located on the front panel of WCC Lite, to access it, remove a transparent front panel cover. Different time lengths of button pressing call for different behaviour. Pressing time Description Indication Short Press System reb...

WCC Lite integrates 1 signal relay (3-way RO connector) with COM (common), NC (normally closed), and NO (normally open) signals. Figure 10: Signal relay connector Maximum switching power is 60W, maximum contact current is 2A, maximum switching voltage is 6...

  Figure 1: Front panel status indication

WCC Lite has an optional dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 6: WCC Lite Dual-SIM card holder To insert SIM cards, r...

WCC Lite has an optional Dual-SIM card modem. To access both SIM cards, remove a transparent front panel cover and press through the marked hole with a small tool until the SIM holder pops out. Figure 5: WCC Lite Dual-SIM card slot

It is recommended to power WCC Lite from a 6W (minimum) 12-24V DC power supply. A full range is 5V to 36V. Figure 3: Power input connector Note: Make sure that the device is compatible with your power source before proceeding! Check the label next to the p...

To mount the device: Secure the top of the mounting clip onto a DIN rail. Push the bottom of a device forward to fix the clip in place. To dismount the device: Pull the red-coloured clip downwards (found at the bottom side of the DIN rail). Pull bac...

For hardware versions older than version 1.4, in case a Wi-Fi connection is needed, connect a Wi-fi antenna to the SMA connector labelled “WIFI“. Select a good antenna placement spot considering the operation environment. Figure 1. Wi-Fi antenna connector (ha...

WCC Lite comes with an optional GSM module.There are a few hardware configurations available:  Without a GSM modem. With single SIM modem (HW version 1.0 - 1.2) - 2G/3G (GPRS, EDGE / UMTS, HSDPA, HSUPA) version - 5.76Mb/s upload, 7.2Mb/s download. UMTS/HSP...

With WCC Lite hardware version 1.4, a digital input functionality has been introduced. Software configuration guidelines are discussed in the WCC Lite internal signals section. It changes state when the voltage is between 12-48V (The supported range is between...

Functionality The SSH key functionality in the WCC Lite device allows you to authenticate securely without needing to enter a password each time you access the device via SSH. This method uses public-key cryptography to ensure a secure connection. This featu...