# Firmware 1.7.0 and 1.11 configurations comparison ## Description This document summarizes configuration differences between WCC Lite firmware versions 1.7.0 and 1.11. Each protocol section contains two separate tables: one for Device Sheet and one for Signal Sheet, following the original documentation structure. (-) indicates that parameter does not exist (+) indicates that parameter exists ## MODBUS Master #### **Signal sheet:**

Parameter	1.7.0	1.11	Description
Periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.

## MODBUS Slave #### **Device sheet:**

Parameter	1.7.0	1.11	Description
Respond\_delay	-	+	Time in milliseconds to wait before sending responses. Disabled if the value is set to 0

#### **Signal sheet:**

Parameter	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.

## DNP3.0 Master #### **Device sheet:**

Parameter	1.7.0	1.11	Description
ip	host	ip
use\_local\_time	-	+	If enabled (1), communication uses system time instead of UTC.

## DNP3.0 Slave #### **Device sheet:**

Parameter	1.7.0	1.11	Description
Control\_code	-	-	DNP3 control model code of CROB signal. TripClose and Pulse control model requires PulseOn/off times to be set
Pulse\_on\_time\_ms	-	-	Pulse ON time in milliseconds, when using Pulse or TripClose control models must be set
Pulse\_off\_time\_ms	-	-	Pulse OFF time in milliseconds, when using Pulse or TripClose control models must be set

## IEC 101 Master #### **Device sheet:**

Parameter	1.7.0	1.11	Description
broadcast\_timesync	-	+	Enables or disables broadcast time sync. If 0 - disabled; if 1 - enabled.

#### **Signal sheet:**

Parameter	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.
tag\_job\_todo	-	+	tag\_job\_todo value must be: communication\_status. If the signal returns 1 – connection is OK; if 2 – disconnected.

## IEC 101 Slave #### **Signal sheet:**

Parameter	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.
Select\_ms	-	+	Polling interval in milliseconds. The time frame between two telegrams from the master.
tag\_job\_todo	-	+	tag\_job\_todo value must be: communication\_status. If the signal returns 1 – connection is OK; if 2 – disconnected.

## IEC 103 Master #### **Device sheet:**

Parameter	1.7.0	1.11	Description
reset\_command\_type	-	+	The user can choose the reset command type between FCB and CU.

#### **Signal sheet:**

Parameter	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.
tag\_job\_todo	-	+	tag\_job\_todo value must be: communication\_status. If the signal returns 1 – connection is OK; if 2 – disconnected.

## IEC 104 Master #### **Device sheet:**

Parameter	1.7.0	1.11	Description
ip	host	ip	Slave device IP

#### **Signal sheet:**

Parameter	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.
tag\_job\_todo	-	+	tag\_job\_todo value must be: communication\_status. If the signal returns 1 – connection is OK; if 2 – disconnected.

## IEC 104 Slave #### **Signal sheet:**

Parameter	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.
tag\_job\_todo	-	+	tag\_job\_todo value must be: communication\_status. If the signal returns 1 – connection is OK; if 2 – disconnected.

## IEC 61850 Server #### **Device sheet:**

Parameter	1.7.0	1.11	Description
Tls	+	-
Edition	+	-
auth	-	+	Authorization type
authorization	+	-

## IEC 61850 Client #### **Device sheet:**

Parameter	1.7.0	1.11	Description
ip	host	ip
auth	-	+	Authorization type
authorization	+	-
event\_history\_size	+	-
model\_filename	-	+	The filename of the client model uploaded to WCC (must contain .client extension)

## MQTT #### **Device sheet:**

Parameter	1.7.0	1.11	Description
ip	host	ip
auth	-	+	Authorization type
Ca\_certificate	-	+	Certificate authority file for TLS connection
Client\_certificate	-	+	Client certificate file for TLS connection
Client\_key	-	+	The private key that corresponds to the client certificate for TLS connection
Client\_id	-	+	User-friendly name for client ID

#### **Signal sheet:**

Signal	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.

## DLMS/COSEM #### **Device sheet:**

Parameter	1.7.0	1.11	Description
poll\_delay\_ms	+	-	Minimum time delay in milliseconds to wait before sending any data on port.

## IEC 62056-21 #### **Device sheet:**

Parameter	1.7.0	1.11	Description
protocol\_control\_char	-	+	Protocol control character
mode\_control\_char	-	+	Mode control character

## WCC Lite Internal Signals #### **Signal sheet:**

Signal	1.7.0	1.11
sim-select (gsm)	-	+
modem-reset (gsm)	-	+

## New Services #### **Signal sheet:**

Service	1.7.0	1.11	Description
Sms\_receiver	-	+	SMS receiver is a service responsible for command execution that was received via text message.

Parameter	1.7.0	1.11	Description
Periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.

Parameter	1.7.0	1.11	Description
Respond\_delay	-	+	Time in milliseconds to wait before sending responses. Disabled if the value is set to 0

Parameter	1.7.0	1.11	Description
periodic\_update\_ms	-	+	Signal value will be published periodically according to the value set.

Parameter	1.7.0	1.11	Description
broadcast\_timesync	-	+	Enables or disables broadcast time sync. If 0 - disabled; if 1 - enabled.

Parameter	1.7.0	1.11	Description
reset\_command\_type	-	+	The user can choose the reset command type between FCB and CU.